DATRON CNC Freseverktøy

Fres Cross cutter Grovfres for aluminium

DATRON Cross Cutter

Fås i dia. 6.0 / 8.0 / 10.0 / 12.0 mm. Passer for 3 kW, 4 kW and 8 kW DATRON spindler.

 

Shadow frame

Dine tekniske fordeler:

  • Høyspesialisert grovverktøy
  • Småspon
  • Høyhastighetsfresing i aluminium
  • Kraftfull sliping

DIne produksjonsforder:

  • Utmerket sponvolum over tid (>100 % mer enn en klassisk balansert 1-skjærs endefres)
  • Maksimal levetid på verktøyet pga trochoidal fresing
  • Spar tid og penger
  • Ingen akkumulering av spon under sprialfresisng
Aluminium
Single Flute MillSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSolid CarbideSharp-Edged Flute

DATRON 2-skjærs Endefres med verktøykjøling, 6/8/10/12 mm skaft

Svært effektivt freseverktøy med verktøykjøling

Shadow frame
  • Høyhastighetsfresing i aluminium, plast, kobber
  • Innv, tilførsel av kjøling
  • Effektiv sponavgang
  • Fleksibel bruk

DATRONs verktøykjøling ble utviklet for å oppnå spesiell lang levetid ved høyhastighetsfresing, ved å sikre en optimal kjøling direkte på fresens skjæreegg. Den innvendige kjølingen med etanol holder arbeidsstykket rent og kan umiddelbart behandles etter frese-/boresyklusen.

Double Flute End Mill with internal coolingAluminiumBrass
Solid Carbide

DATRON 3-, 4- og 6-skjærs Endefreser

Uansett om det er med tre, fire eller 6 skjærekanter  – alle DATRON verktøy utviklet for maskinering i stål har en stabil skjæregeometri og heavy duty belegg.

Shadow frame

DATRON 3-skjærs Endefres

  • hardmeatll endefres i Ultra-finkornet kvalitet
  • 3-skjær
  • 30° høyrevridd spiral
  • skaft uten spennflate DIN 6535-HA

Denne endefresen har en svært kort kuttflate og et spesielt belegg, som resulterer i  en svært lang verktøylevetid.

CNC Milling Tool Triple Flute End Mill DATRON
Brass
Three FlutesSpiral Angle 30°Shank Form DIN 6535 Form HAFeed DirectionSharp-Edged Flute
Shadow frame

DATRON 3-skjærs Endefres med Toric Cut

  • hardmeatll endefres i Ultra-finkornet kvalitet
  • 3-skjærs med flat bunn
  • 45° høyrevridd spiral
  • skaft med spennflate DIN 6535-HB
  • senterkutt med ett langt skjær

Toric Cut gjør disse  verktøyene spesielt egnet for fresing uten forstyrrende konturer.

CNC Milling Tool Triple Flute End Mill with Toric Cut DATRON
AluminiumBrassCopper
Three FlutesPoint Angle 130°Shank Form DIN 6535 Form HBFeed DirectionSharp-Edged Flute
Shadow frame

DATRON 3-skjærs Endefres med Toric Cut for Skummateriale

  • hardmeatll endefres i Ultra-finkornet kvalitet
  • 3-skjærs med flat bun
  • 30° høyrevridd spiral
  • skaft spennflate DIN 6535-HB
  • senterkutt med ett langt skjær
  • polerte skjærekanter

De nye skumfresene har finpolerte skjærekanter og sponkanaler spesielt tilpasset fresing i skum. I tillegg har DATRON klart å perfeksjonere de spesielle skjærekantgeometriene og spiralvinklene i freseserien for skumverktøy.

Shadow frame

DATRON Triple Flute End Mill, Copper roughing mill

  • Micrograin solid carbide end mill
  • with three flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HB
  • centre cut with one long flute
  • ground-in chip cutter

Due to the three flutes with ground-in chip cutter, very high feed rates are possible with the corresponding deptch adjustment. Copper is machines almost burr free.

Shadow frame

DATRON Triple Flute End Mill, Smoothing Mill for Copper

  • Micrograin solid carbide end mill
  • with three flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HB
  • centre cut with one long flute

Due to the three flutes with a special clearance angle geometry an extremely good workpiece surface quality is achieved in the finishing process.

Shadow frame

DATRON Four Flute End Mill

  • Micrograin solid carbide end mill
  • with four flutes
  • 30° upcut spiral
  • shank with clamping surface DIN 6535-HB
  • centre cut

The four-flute end mill is available in two versions. With a very short flute for even more stability and with a long flute for thick materials machining. Due to their standard Alcrona coating, these tools achieve very high durability even when machining hard materials.

CNC Milling Tool Four Flute End Mill, short version DATRON
BrassCopper
Four FlutesSpiral Angle 30°Shank Form DIN 6535 Form HBFeed DirectionMicro GrainSharp-Edged Flute
Shadow frame

DATRON Four Flute End Mill with Edge Radius

  • Micrograin solid carbide end mill
  • with four flutes
  • 30° upcut spiral
  • edge radius
  • shank without clamping surface DIN 6535-HA
  • centre cut
  • toric cut

The special characteristics of this end mill are the rounded edges and the standard toric cut. These tools have a special X.CEED coating.

CNC Milling Tool Four Flute End Mill with Edge Radius DATRON
BrassCopper
Four FlutesSpiral Angle 30°Flute with Edge RadiusShank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Four Flute End Mill, Pitch 35°/38°

  • Micrograin solid carbide end mill
  • with four flutes
  • 35°/38° upcut spiral
  • shank with clamping surface DIN 6535-HB
  • centre cut with two long front side flutes

Due to its different helical pitch, this milling tool runs extremely smoothly and chips are removed very quickly. As standard these tools are supplied with an Alcrona coating.

CNC Milling Tool Four Flute End Mill, Pitch 35°/38°, Short Version DATRON
BrassCopper
Four FlutesSpiral Angle 35°/38°Shank Form DIN 6535 Form HBFeed DirectionSharp-Edged Flute
Shadow frame

DATRON Four Flute End Mill, Roughing Mill

  • Micrograin solid carbide end mill
  • with four flutes
  • 25° upcut spiral
  • shank with clamping surface DIN 6535-HB
  • centre cut with two long front side flutes

The roughing end mill is available in two versions. With a very short flute for even more stability and with a long flute for thick materials machining. Due to their standard X.CEED coating and the special cutting geometry, these tools achieve very high durability even when machining hard materials.

CNC Milling Tool Four Flute End Mill, Roughing Mill, Short Version DATRON
BrassCopper
Four FlutesSpiral Angle 25°Shank Form DIN 6535 Form HBFeed DirectionSharp-Edged Flute
Shadow frame

DATRON Six Flute End Mill

  • Micrograin solid carbide end mill
  • with six flutes
  • 50° upcut spiral
  • radial under cut
  • shank without clamping surface DIN 6535-HA
  • without centre cut
  • partly with edge radius

This end mill has a very short flute length and a special coating, which results in a very long tool life.

DATRON 3-, 4- og 6-skjærs Endefreser

Uansett om det er med tre, fire eller 6 skjærekanter  – alle DATRON verktøy utviklet for maskinering i stål har en stabil skjæregeometri og heavy duty belegg.

Shadow frame

DATRON 3-skjærs Endefres

  • hardmeatll endefres i Ultra-finkornet kvalitet
  • 3-skjær
  • 30° høyrevridd spiral
  • skaft uten spennflate DIN 6535-HA

Denne endefresen har en svært kort kuttflate og et spesielt belegg, som resulterer i  en svært lang verktøylevetid.

CNC Milling Tool Triple Flute End Mill DATRON
Brass
Three FlutesSpiral Angle 30°Shank Form DIN 6535 Form HAFeed DirectionSharp-Edged Flute
Shadow frame

DATRON 3-skjærs Endefres med Toric Cut

  • hardmeatll endefres i Ultra-finkornet kvalitet
  • 3-skjærs med flat bunn
  • 45° høyrevridd spiral
  • skaft med spennflate DIN 6535-HB
  • senterkutt med ett langt skjær

Toric Cut gjør disse  verktøyene spesielt egnet for fresing uten forstyrrende konturer.

CNC Milling Tool Triple Flute End Mill with Toric Cut DATRON
AluminiumBrassCopper
Three FlutesPoint Angle 130°Shank Form DIN 6535 Form HBFeed DirectionSharp-Edged Flute
Shadow frame

DATRON 3-skjærs Endefres med Toric Cut for Skummateriale

  • hardmeatll endefres i Ultra-finkornet kvalitet
  • 3-skjærs med flat bun
  • 30° høyrevridd spiral
  • skaft spennflate DIN 6535-HB
  • senterkutt med ett langt skjær
  • polerte skjærekanter

De nye skumfresene har finpolerte skjærekanter og sponkanaler spesielt tilpasset fresing i skum. I tillegg har DATRON klart å perfeksjonere de spesielle skjærekantgeometriene og spiralvinklene i freseserien for skumverktøy.

Shadow frame

DATRON Triple Flute End Mill, Copper roughing mill

  • Micrograin solid carbide end mill
  • with three flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HB
  • centre cut with one long flute
  • ground-in chip cutter

Due to the three flutes with ground-in chip cutter, very high feed rates are possible with the corresponding deptch adjustment. Copper is machines almost burr free.

Shadow frame

DATRON Triple Flute End Mill, Smoothing Mill for Copper

  • Micrograin solid carbide end mill
  • with three flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HB
  • centre cut with one long flute

Due to the three flutes with a special clearance angle geometry an extremely good workpiece surface quality is achieved in the finishing process.

Shadow frame

DATRON Four Flute End Mill

  • Micrograin solid carbide end mill
  • with four flutes
  • 30° upcut spiral
  • shank with clamping surface DIN 6535-HB
  • centre cut

The four-flute end mill is available in two versions. With a very short flute for even more stability and with a long flute for thick materials machining. Due to their standard Alcrona coating, these tools achieve very high durability even when machining hard materials.

CNC Milling Tool Four Flute End Mill, short version DATRON
BrassCopper
Four FlutesSpiral Angle 30°Shank Form DIN 6535 Form HBFeed DirectionMicro GrainSharp-Edged Flute
Shadow frame

DATRON Four Flute End Mill with Edge Radius

  • Micrograin solid carbide end mill
  • with four flutes
  • 30° upcut spiral
  • edge radius
  • shank without clamping surface DIN 6535-HA
  • centre cut
  • toric cut

The special characteristics of this end mill are the rounded edges and the standard toric cut. These tools have a special X.CEED coating.

CNC Milling Tool Four Flute End Mill with Edge Radius DATRON
BrassCopper
Four FlutesSpiral Angle 30°Flute with Edge RadiusShank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Four Flute End Mill, Pitch 35°/38°

  • Micrograin solid carbide end mill
  • with four flutes
  • 35°/38° upcut spiral
  • shank with clamping surface DIN 6535-HB
  • centre cut with two long front side flutes

Due to its different helical pitch, this milling tool runs extremely smoothly and chips are removed very quickly. As standard these tools are supplied with an Alcrona coating.

CNC Milling Tool Four Flute End Mill, Pitch 35°/38°, Short Version DATRON
BrassCopper
Four FlutesSpiral Angle 35°/38°Shank Form DIN 6535 Form HBFeed DirectionSharp-Edged Flute
Shadow frame

DATRON Four Flute End Mill, Roughing Mill

  • Micrograin solid carbide end mill
  • with four flutes
  • 25° upcut spiral
  • shank with clamping surface DIN 6535-HB
  • centre cut with two long front side flutes

The roughing end mill is available in two versions. With a very short flute for even more stability and with a long flute for thick materials machining. Due to their standard X.CEED coating and the special cutting geometry, these tools achieve very high durability even when machining hard materials.

CNC Milling Tool Four Flute End Mill, Roughing Mill, Short Version DATRON
BrassCopper
Four FlutesSpiral Angle 25°Shank Form DIN 6535 Form HBFeed DirectionSharp-Edged Flute
Shadow frame

DATRON Six Flute End Mill

  • Micrograin solid carbide end mill
  • with six flutes
  • 50° upcut spiral
  • radial under cut
  • shank without clamping surface DIN 6535-HA
  • without centre cut
  • partly with edge radius

This end mill has a very short flute length and a special coating, which results in a very long tool life.

DATRON Micro-Tannet endefres

Slipende materialer, slik som CRP, GRP eller kretskortmateriale, kan pålitelig bearbeides til en lav pris med mikrotannede freser fra DATRON.

Shadow frame

DATRON Micro-Tannet Endefres

  • hardmetall endefres i Ultra-finkornet kvalitet
  • micro-tannet
  • fiskehaleslipt bunn
  • skaft uten spennflate DIN 6535-HA

Disse verktøyene er svært godt egnet for bearbeiding av kretskort eller testadaptere.

CNC Milling Tool Micro-Toothed End Mill DATRON
GRPFR4Fabric-Base Laminate
Eight FlutesShank Form DIN 6535 Form HAFeed Direction
Sharp-Edged Flute
Shadow frame

DATRON Micro-Tannet Endefres, Belagt 

  • hardmeatll endefres i Ultra-finkornet kvalitet
  • micro-tannet
  • fiskehaleslipt bunn
  • skaft uten spennflate DIN 6535-HA
  • X.CEED Belagt/Diamant-belagt

Fordi disse verktøyene er mikrotannet og belagt er levetid lang, selv med ekstremt slitende materialer.

CNC Milling Tool Micro-Toothed End Mill, coated DATRON
GRPFR4Fabric-Base Laminate
Eight FlutesShank Form DIN 6535 Form HAFeed Direction
Sharp-Edged Flute

Endefres enskjærs CNC fres verktøy

DATRON Single Flute End Mills

These tools are available with various cutting lengths and shank diameters. The balanced single flute end mill – an exclusive DATRON product. Powerful, economical and patented.

Shadow frame

DATRON Single Flute End Mill

  • Micrograin solid carbide end mill
  • with single flute and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

This specially-cut end mill is designed for very fast feed rates and very high chip removal capacity.

CNC Milling Tool Single Flute End Mill DATRON
AluminiumBrassCopper
GoldPlastic
Single Flute MillSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame
DATRON 4-in-1 Single Flute End Mill
  1. polished chip space
  2. polished flute
  3. counter-balanced cut
  4. flat end-mill
  • Extended spindle life
  • Excellent surfaces
  • Reduced machining cycles
  • Lower tool cost

Due the polished chip space and the polished flute in conjunction with a counter-balanced cut, our new-balanced single flute end mill allows even higher infeed and feed rates compared to standard single flute end mills.

Exclusive at DATRON: Due to the patented counterbalance cut in combination with the polished edge and chip space, even higher infeed and feed rates are possible. In addition, the best possible surfaces are achieved, thanks to the optimized frontal geometry.

CNC Milling Tool 4-in-1 Single Flute End Mill DATRON
AluminiumBrassCopper
GoldPlastic
Single Flute MillSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

Single Flute End Mill Stepped

  • Optimized chip flute for fast and efficient chip removal
  • Sharp cutting edge and wiper flat for excellent surface quality
  • Patented balanced tool tip for maximum smoothness and low-vibration operation
AluminiumWood
Brass
Solid Carbide
Shadow frame

DATRON Single Flute End Mill with Polished Cutting Edge

  • Micrograin solid carbide end mill
  • with single flute and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

For this tool, optimised for plastic machining, in addition to the additional polish-grinding, the cutting geometry was also reworked, the cutting angles are now designed much sharper. Compared to universal single-flutes, this leads to a considerably more sharp cutting edge. With this, top-quality surface results can be realised on plastic contours.

CNC Milling Tool Single Flute End Mill with Polished Cutting Edge DATRON
Plastic
Single Flute MillSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Single Flute End Mill with Toric Cut

  • Micrograin solid carbide end mill
  • with single flute and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA
  • toric cut

With this specially ground milling tool, you can perform particularly deep milling work with high feed rates in the material. The large chip groove allows optimal chip removal.

CNC Milling Tool Single Flute End Mill with Toric Cut DATRON
AluminiumBrassCopper
GoldPlastic
Single Flute MillSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Single Flute End Mill, Specially Balanced

  • Micrograin solid carbide end mill
  • with single flute and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA
  • specially balanced
  • toric cut

These tools are available with various cutting lengths and shank diameters. The patented balanced single flute end mill – an exclusive DATRON product. Powerful, economical and highly efficient.

CNC Milling Tool Single Flute End Mill, Specially Balanced DATRON
AluminiumBrassCopper
GoldPlastic
Single Flute MillSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Single Flute End Mill, Left Hand Spiral, Right Hand Cutting

  • Micrograin solid carbide end mill
  • with single flute and flat bottom
  • 30° Downcut spiral
  • shank without clamping surface DIN 6535-HA

Due to the downcut spiral, the cutting pressure during milling is exerted downward, preventing especially delicate work pieces from being lifted.

CNC Milling Tool Single Flute End Mill, Left Hand Spiral, Right Hand Cutting DATRON
AluminiumBrassCopper
GoldPlastic
Single Flute MillSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute

DATRON Double Flute End Mills

DATRON double flute end mills are available in special models. With extra short cutting edge, toric cut, or stepped.
New DATRON products: coated micro-tools for steel machining with extra short flutes.

Shadow frame

DATRON Double Flute End Mill, 3 mm Shank

  • Micrograin solid carbide end mill
  • with double flute and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

DATRON’s double flute end mills are availabe in special versions: with extra short flutes, toric cut or stepped. These tools are especially suitable to produce a high surface quality. The symmetrical arrangement of the flutes and the resulting high concentricity, make these tools also suitable for the production of fits. In addition, coated micro tools with an extremely short flute for steel machining are also available.

CNC Milling Tool Double Flute End Mill, 3 mm Shank DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Double Flute End Mill, 6 mm Shank

  • Micrograin solid carbide end mill
  • with double flute and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

DATRON’s double flute end mills are availabe in special versions: with extra short flutes, toric cut or stepped. These tools are especially suitable to produce a high surface quality. The symmetrical arrangement of the flutes and the resulting high concentricity, make these tools also suitable for the production of fits. In addition, coated micro tools with an extremely short flute for steel machining are also available.

CNC Milling Tool Double Flute End Mill, 6 mm Shank DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Double Flute End Mill with Edge Radius, Stepped

  • Micrograin solid carbide end mill
  • with double flute and flat bottom
  • edge radius
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

This tool has an edge radius, which increases the tool life. Models with toric cut have a large useable depth.

CNC Milling Tool Double Flute End Mill with Edge Radius, Stepped DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Flute with Edge Radius
Shank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Double Flute End Mill with Edge Radius

  • Micrograin solid carbide end mill
  • with double flute and flat bottom
  • edge radius
  • 25° upcut spiral
  • shank without clamping surface DIN 6535-HA
  • toric cut

This tool has an edge radius, which increases the tool life. Models with toric cut have a large useable depth.

CNC Milling Tool Double Flute End Mill with Edge Radius DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 25°Flute with Edge Radius
Shank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Double Flute End Mill with Edge Radius and polished flute

  • Micrograin solid carbide end mill
  • with double flute and flat bottom
  • edge radius
  • 25° upcut spiral
  • shank without clamping surface DIN 6535-HA
  • with polished cutting edge

The advanced face geometry of these face end mills, in conjunction with a polishing cut allows transparent results when face milling acrylic materials.

Shadow frame

DATRON Double Flute End Mill, Stepped

  • Micrograin solid carbide end mill
  • with two flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

With stepped double flute end mills, the cutting edge diameter is considerably larger than the shaft diameter. This tool is ideally suited for milling over. With high feed rates and low infeed, large surfaces can be milled over in a short time. Due to the sharp-edged corners, it is also possible to perform contour machining.

CNC Milling Tool Double Flute End Mill, Stepped DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute

Shadow frame

DATRON Double Flute End Mill with Toric Cut

  • Micrograin solid carbide end mill
  • with two flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA
  • toric cut

The shank´s toric cut permits deeper machining.

CNC Milling Tool Double Flute End Mill with Toric Cut DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Double Flute End Mill, Contour Milling

  • Micrograin solid carbide end mill
  • with two flutes and flat bottom
  • 45° upcut spiral
  • shank without clamping surface DIN 6535-HA

Thanks to the 45° upcut spiral these tools are specially suited for the machining of contours.

CNC Milling Tool Double Flute End Mill, Contour Milling DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesPoint Angle 130°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Double Flute End Mill, HSC+

  • Micrograin solid carbide end mill
  • with two flutes and flat bottom
  • 15° upcut spiral
  • shank without clamping surface DIN 6535-HA

The special feature of this mill is the steep upcut angle. The chips are removed very quickly from the work piece. In many cases this results in extremely high feed rates.

CNC Milling Tool Double Flute End Mill, HSC+ DATRON
AluminiumBrassCopper
Plastic
Two FlutesSpiral Angle 15°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute
Shadow frame

DATRON Double Flute End Mill for Steel Machining

  • Micrograin solid carbide end mill
  • with two flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

The cutting geometry of these micro tools is designed for Steel machining. In combination with the standard X.CEED coating, these tools have a high tool life and provide excellent surface quality.

CNC Milling Tool Double Flute End Mill for Steel Machining DATRON
BrassCopperSteel
Two FlutesSpiral Angle 30°Shank Form DIN 6535 Form HA
Feed DirectionSharp-Edged Flute

DATRON Thread Mills

Thread milling in a flash from M1.0. Innovative milling thread mill: core hole drilling and thread milling with only one tool, in a single work step.

Shadow frame

DATRON Thread Mill

  • Micrograin solid carbide thread mill
  • with four flutes
  • shank without clamping surface DIN 6535-HA

With this tool, threads from M1.0 onwards can be milled directly with an HF spindle. Threads no longer need to be machined outside the high-speed milling machine.

CNC Milling Tool Thread Mill DATRON
AluminiumBrassCopper
GoldPlastic
Four FlutesShank Form DIN 6535 Form HA
Shadow frame

DATRON Milling Thread Mill

  • Micrograin solid carbide milling thread mill
  • with three flutes
  • shank without clamping surface DIN 6535-HA

Specially effective thread milling can be done with the innovative milling thread mill from DATRON. With this tool the centre hole and milling thread can be machined at one time. This special tool is legally protected by a utility patent.

CNC Milling Tool Milling Thread Mill DATRON
AluminiumBrassCopperPlastic
Three FlutesShank Form DIN 6535 Form HA
Shadow frame
DATRON Multi Thread Mill
  • Micrograin solid carbide multi thread mill
  • shank without clamping surface DIN 6535-HA
  • with 45° countersink section

The multi-toothing of this tool allows a complete thread cut within one helix. This way, threads can be produced in an optimum amount of time and extremely efficiently. The integrated 45° countersink chamfer is for automatic deburring.

CNC Milling Tool Multi Thread Mill DATRON
AluminiumBrassCopperPlastic
Shank Form DIN 6535 Form HA

DATRON Ball Nose/External Radius End Mills

Especially designed for 3D machining, DATRON’s ball nose end mills are offered in several versions. In addition to one, two and four flute versions, exclusive polished variants as well as micro-versions are available, exclusive from DATRON.

Shadow frame

DATRON Ball Nose End Mill, One Flute

  • Micrograin solid carbide end mill
  • with single flute and radius bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

With this specially ground milling tool, with a small flute and ball nose end very outstanding results can be performed with high feed rates in the material. The large chip groove allows for optimal chip removal and an excellent surface finish.

Shadow frame

DATRON Ball Nose End Mill, polished, One Flute

  • Micrograin solid carbide end mill
  • with single flute and radius bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA
  • with polished cutting edge

Specially designed for 3D machining of transparent plastics. The extremely sharp cutting geometry with a polishing cut ensures highest-quality surface results, the cutting construction allows still higher material feed rates, which significantly shortens production times.

Shadow frame

DATRON Ball Nose End Mill, Double Flute

  • Micrograin solid carbide end mill
  • with two flutes
  • 30° upcut spiral
  • centre cut
  • shank without clamping surface DIN 6535-HA
CNC Milling Tool Ball Nose End Mill, Double Flute DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Ball Nose
Shank Form DIN 6535 Form HAFeed DirectionMicro Grain
Shadow frame

DATRON Ball Nose End Mill, Four Flutes, Short Version

  • Micrograin solid carbide end mill
  • with four flutes
  • 30° upcut spiral
  • centre cut, full radius
  • shank with clamping surface DIN 6535-HB
  • with Alcrona coating
CNC Milling Tool Ball Nose End Mill, Four Flutes, Short Version DATRON
Copper
Four FlutesSpiral Angle 30°Ball Nose
Shank Form DIN 6535 Form HBFeed Direction
Shadow frame

DATRON Ball Nose End Mill, Four Flutes, Long Version

  • Micrograin solid carbide end mill
  • with four flutes
  • 30° upcut spiral
  • centre cut, full radius
  • shank with clamping surface DIN 6535-HB
  • with Alcrona Coating
CNC Milling Tool Ball Nose End Mill, Four Flutes, Long Version DATRON
Copper
Four FlutesSpiral Angle 30°Ball Nose
Shank Form DIN 6535 Form HBFeed Direction
Shadow frame

DATRON Ball Nose End Mill, Two Flutes with Toric Cut

  • Micrograin solid carbide end mill
  • with two flutes
  • 30° upcut spiral
  • centre cut
  • toric cut
  • shank without clamping surface DIN 6535-HA

Thanks to the toric cut of the shaft the work piece can be machined more deeply.

CNC Milling Tool Ball Nose End Mill, Two Flutes with Toric Cut DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Ball Nose
Shank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Micro Ball Nose End Mill with Toric Cut

  • Micrograin solid carbide end mill
  • with two flutes
  • 30° upcut spiral
  • centre cut
  • toric cut
  • shank without clamping surface DIN 6535-HA

Thanks to the toric cut of the shaft the work piece can be machined more deeply.

CNC Milling Tool Micro Ball Nose End Mill with Toric Cut DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesSpiral Angle 30°Ball Nose
Shank Form DIN 6535 Form HAFeed DirectionMicro Grain
Shadow frame

DATRON External Radius End Mill

  • Micrograin solid carbide external radius end mill
  • with two flutes or up to four flutes
  • with specially cut edges for the machining of external edges
  • shank without clamping surface DIN 6535-HA

This end mill is specially designed for the optimum machining of external radii.

CNC Milling Tool External Radius End Mill DATRON
AluminiumBrassCopper
GoldPlastic
2/4 Flutes MillShank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON External Radius End Mill, Polished

  • Micrograin solid carbide external radius end mill
  • with three flutes
  • with specially cut edges for the machining of external edges
  • shank without clamping surface DIN 6535-HA
  • with polished cutting edge

The external radius end mill especially developed for acrylic has an extremely sharp cutting geometry with a polishing cut and is therefore ideally suited for creating transparent edge roundings.

Shadow frame

DATRON Deburring End Mill, two flutes

  • Micrograin solid carbide external radius end mill
  • with two flutes
  • with specially cut edges for the machining of external edges
  • shank without clamping surface DIN 6535-HA

These outer radius end mills were specifically designed for the automated deburring of counter plate grooves. The tools have a uniform outer radius of 0.3 mm. With face diameters between 0.9 and 2.4 mm all standard counter plate groove widths are covered. The flute geometry optimised for steel machining guarantees excellent cutting results with excellent durability.

DATRON T-Slotting/Dovetail Mills

Shadow frame

DATRON T-Slotting Mill

  • Micrograin solid carbide T-slotting mill
  • with two flutes or up to six flutes
  • shank without clamping surface DIN 6535-HA

These special tools allow machining T-slots and lateral slots on contour surfaces. Thus, re-clamping operations can be reduced and production times shortened.

CNC Milling Tool T-Slotting Mill DATRON
AluminiumBrassCopper
GoldPlastic
2/6 flutes millShank Form DIN 6535 Form HAFeed Direction
Sharp-Edged Flute
Shadow frame

DATRON Dovetail Milling Tool

  • Micrograin solid carbide end mill
  • with two flutes
  • shank without clamping surface DIN 6535-HA

The double-edged special milling tools are excellently suited for producing dovetail grooves and rear-side deburring or chamfering of the bottom sides of work pieces. This minimises reclamping operations and reduces production times.

CNC Milling Tool Dovetail Milling Tool DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesShank Form DIN 6535 Form HAFeed Direction
Sharp-Edged Flute

DATRON Drills

Reliable drilling from a diameter of 0.1 mm.

Shadow frame

DATRON Drill, 3 mm Shank

  • Micrograin solid carbide drill
  • with 130° point angle
  • shank without clamping surface DIN 6535-HA
CNC Milling Tool Drill, 3 mm Shank DATRON
AluminiumBrassCopper
Plastic
Two FlutesSpiral Angle 30°Point Angle 130°
Shank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Drill, 3 mm Shank

  • Micrograin solid carbide drill
  • with 165° point angle
  • shank without clamping surface DIN 6535-HA
CNC Milling Tool Drill, 3 mm Shank DATRON
AluminiumBrassCopper
Plastic
Two FlutesSpiral Angle 30°Point Angle 165°
Shank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Drill, 1/8″ Shank

  • Micrograin solid carbide drill
  • with 130° point angle
  • shank without clamping surface DIN 6535-HA
CNC Milling Tool Drill, 1/8” Shank DATRON
AluminiumBrassCopper
Plastic
Two FlutesSpiral Angle 30°Point Angle 130°
Shank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Drill, 1/8″ Shank

  • Micrograin solid carbide drill
  • with 165° point angle
  • shank without clamping surface DIN 6535-HA
CNC Milling Tool Drill, 1/8” Shank DATRON
AluminiumBrassCopper
Plastic
Two FlutesSpiral Angle 30°Point Angle 165°
Shank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Drill, 6 mm Shank

  • Micrograin solid carbide drill
  • with 130° point angle
  • shank without clamping surface DIN 6535-HA
  • suitable for thick sheet metal material up to 20 mm
CNC Milling Tool Drill, 6 mm Shank DATRON
AluminiumBrassCopper
Plastic
Two FlutesSpiral Angle 30°Point Angle 130°
Shank Form DIN 6535 Form HAFeed Direction

DATRON Countersink/Milling Countersink Tool

Shadow frame

DATRON Countersink Tool

  • Micrograin solid carbide countersink tool
  • with two flutes or up to four flutes
  • shank without clamping surface DIN 6535-HA

These mould tools allow machining countersinks and chamfers with highest surface quality. The deeply cut chip chambers guarantee optimum chip evacuation and allow high feed rates

CNC Milling Tool Countersink Tool DATRON
AluminiumBrassCopper
GoldPlastic
Two to Four FlutesShank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Countersink Tool for Foam

  • Micrograin solid carbide countersink tool
  • with three flutes
  • shank without clamping surface DIN 6535-HA

The new foam mills, besides having finely polished cutters also feature chip channels adjusted for PU foam machining. In addition, DATRON especially perfected the special blade geometries and helix angles of the foam tool series.

Shadow frame

DATRON Countersink Tool for Acrylic

  • Micrograin solid carbide countersink tool
  • with three or six flutes
  • shank without clamping surface DIN 6535-HA
  • with polished cutting edge

The especially developed countersink for acrylic machining has an extremely sharp cutting geometry with a polishing cut for high-quality chamfers and countersinks, as well as 15° helixes and large chip chambers for optimal chip evacuation.

Shadow frame

DATRON Milling Countersink Tool

  • Micrograin solid carbide milling countersink tool
  • with single flute
  • centre cut
  • shank without clamping surface DIN 6535-HA

This combination tool has a cylindrical milling range, as well as a conical countersink part. The groove and chamfer can be realized in only one work step. This way, the tool change can be omitted, which reduces the production time.

CNC Milling Tool Milling Countersink Tool DATRON
AluminiumBrassCopper
GoldPlastic
Single Flute MillShank Form DIN 6535 Form HAFeed Direction
Sharp-Edged Flute
Shadow frame

DATRON V-Slotting End Mill

  • Micrograin solid carbide
  • with two flutes
  • centre cut
  • shank without clamping surface DIN 6535-HA

The particular advantage of these special tools lies in their over centre cutting face geometry. This allows not only making of chamfers and countersinks but also the milling of V-Slots, which are needed especially in bending technology applications.

DATRON Single Flute End Mill with Polished Cutting Edge

  • Micrograin solid carbide end mill
  • with single flute and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HA

For this tool, optimised for plastic machining, in addition to the additional polish-grinding, the cutting geometry was also reworked, the cutting angles are now designed much sharper. Compared to universal single-flutes, this leads to a considerably more sharp cutting edge. With this, top-quality surface results can be realised on plastic contours.

Shadow frame

DATRON Countersink Tool for Acrylic

  • Micrograin solid carbide countersink tool
  • with three or six flutes
  • shank without clamping surface DIN 6535-HA

DATRON Face Milling Tool

Highly efficient face milling with HSK interface and replaceable cutting inserts.

Shadow frame

DATRON Face Milling Tool

  • Monoblock tool
  • with two replaceable cutting inserts
  • based on HSK

This HSK-E 25 based monoblock tool has been developed for highly efficient milling over. The required penetration angle is 3-5°. Solid carbide replaceable cutting inserts are available for various materials.

CNC Milling Tool Face Milling Tool DATRON
AluminiumBrassCopper
GoldPlastic
Two FlutesFeed Direction

DATRON Standard Engraving Tool

Now the DATRON engraving tool is also available as a balanced model and for steel machining.

Shadow frame
DATRON Standard Engraving Tool
  • Micrograin solid carbide engraving tool
  • with single flute
  • conic tool tip
  • shank without clamping surface DIN 6535-HA
CNC Milling Tool Standard Engraving Tool DATRON
AluminiumBrassCopper
GoldPlastic
Single Flute MillShank Form DIN 6535 Form HAFeed Direction
Shadow frame
DATRON Standard Engraving Tool, specially balanced
  • Micrograin solid carbide engraving tool
  • with single flute
  • conic tool tip
  • shank without clamping surface DIN 6535-HA
  • with counter-balancing cut

DATRON standard engraving tools are designed for engraving in aluminium, non-ferrous metals and plastics. The variants with patented counter-balancing cut allow high-speed applications without vibrations.

Shadow frame

DATRON Standard Engraving Tool for Steel Engraving

  • Micrograin solid carbide engraving tool
  • with single flute
  • shank without clamping surface DIN 6535-HA
  • For Steel engraving

DATRON’s engraving tools for steel machining are clearly designed with a reinforced cutting geometry and achieve highest durability.

CNC Milling Tool Standard Engraving Tool for Steel engraving DATRON
Steel
Single Flute MillShank Form DIN 6535 Form HAFeed Direction
Shadow frame

DATRON Standard Engraving Tool for Hard-Metal Machining

  • Micrograin solid carbide engraving tool
  • with single flute
  • shank without clamping surface DIN 6535-HA
  • for Steel engraving
  • with reinforced flutes

These engraving tools developed for hard-metal machining have a standard special coating, an extremely short halving and reinforced support geometry. Thus it is also possible to achieve cost-effective machining in standard times even with the hardest materials.

DATRON Triple Flute End Mill with Toric Cut for PU Foam

  • Micrograin solid carbide end mill
  • with three flutes and flat bottom
  • 30° upcut spiral
  • shank without clamping surface DIN 6535-HB
  • centre cut with one long flute
  • with polished cutting edge

The new foam mills, besides having finely polished cutters also feature chip channels adjusted for PU foam machining. In addition, DATRON especially perfected the special blade geometries and helix angles of the foam tool series.

Shadow frame

DATRON Countersink Tool for Foam

  • Micrograin solid carbide countersink tool
  • with three flutes
  • shank without clamping surface DIN 6535-HA

The new foam mills, besides having finely polished cutters also feature chip channels adjusted for PU foam machining. In addition, DATRON especially perfected the special blade geometries and helix angles of the foam tool series.

Foam

DATRON Diamond Milling Tool

The new CVD cutting material for the cutting of CRP, GRP, PCB and Plastic exceeds the standard PCD cutting material with regard toabrasion resistance, tool life and surface finish.

Shadow frame

DATRON Diamond Mill for CRP/GRP

  • Micrograin solid carbide end mill with soldered Diamond flute
  • with single/double flute and flat bottom
  • shank without clamping surface DIN 6535-HA

Compared to Micrograin SC tools this specially designed CVD Diamond milling tool allows for higher feed rates at very high tool life.

CNC Milling Tool Diamond Mill for CRP/GRP DATRON
CRPGRPFR4
Fabric-Base Laminate
1-2 FlutesCVDSpiral Angle 0°
Shank Form DIN 6535 Form HASharp-Edged Flute